Susan Road, Faisalabad Workshop•Direct Delivery & Fitting Across Punjab & Lahore•Mon–Thu, Sat–Sun 9am–9pm

Frequently Asked Questions: Metal Fabrication & Commercial Kitchens

Direct, technical answers about stainless steel metallurgical grades (AISI 304 vs 316), sheet gauge thickness, commercial kitchen ventilation calculation, custom driveway gates, and direct workshop logistics between Faisalabad and Lahore.

Stainless Steel & MaterialsCommercial Kitchen EquipmentExhaust Hoods & VentilationSteel Fabrication & GatesPricing, Quotes & GuaranteesFaisalabad & Lahore Logistics

Stainless Steel & Materials

What is the difference between AISI 304 and AISI 316 stainless steel?

AISI 304 contains 18% chromium and 8% nickel, making it the industry standard for commercial kitchens, prep tables, and sinks. AISI 316 adds 2–3% molybdenum, providing superior corrosion resistance against high chlorides, sea air, and harsh acidic sanitizers, but at a 25–40% higher material cost.

Why should 201 or 202 stainless steel never be used in commercial kitchens?

201 and 202 grades substitute manganese and nitrogen for nickel to cut costs. Under daily commercial kitchen exposure to moisture, organic acids, and salt, 201 rusts and develops surface pitting within months, violating food safety standards.

What sheet thickness in millimetres corresponds to 16, 18, and 14 gauge?

Under standard manufacturing standards (ASTM A240), 18-gauge corresponds to 1.2 mm, 16-gauge corresponds to 1.5 mm, and 14-gauge corresponds to 2.0 mm. Gauge numbers decrease as metal thickness increases.

What thickness is recommended for commercial kitchen prep table tops?

For standard restaurant prep tables, 1.2 mm (18-gauge) AISI 304 stainless steel reinforced with welded undershelf hat channels is standard. For high-impact butcher tables and heavy cooking equipment, 1.5 mm (16-gauge) is required to prevent surface deflection.

Is 304 stainless steel magnetic?

In its raw annealed mill state, 304 stainless steel is non-magnetic. However, mechanical cold working such as shearing, hydraulic brake bending, and deep drawing can induce slight localized magnetic permeability along cut and formed edges without compromising chemical alloy purity.

How can a customer test if their stainless equipment is genuine AISI 304?

Clients can perform a chemical molybdenum / acid spot test using a standard stainless testing reagent drop with a low-voltage battery circuit. AISI 304 shows no yellow/black reaction, whereas inferior 200-series grades react immediately with dark surface staining.

What is a No. 4 brushed satin finish on stainless steel?

A No. 4 finish is an architectural directional satin polish produced with 120–180 grit abrasives. It offers a smooth, non-reflective surface that disguises everyday scratches, resists fingerprints, and allows easy wipe-down sanitation in commercial kitchens.

Can mild steel be used inside commercial food preparation areas?

No. Mild steel oxidizes and rusts rapidly when exposed to humidity, water, and food acids, even if painted. Only food-grade AISI 304 or 316 stainless steel should be used for surfaces in contact with food or subjected to wet washdowns.

How do you prevent tea staining and surface rust on stainless welds?

We utilize 100% pure argon shielding gas during TIG welding to prevent atmospheric nitrogen contamination, followed by mechanical grinding and passivating pickling paste to restore the protective chromium oxide layer.

What is the tolerance variation on stainless steel sheet thickness in Pakistan?

Mill tolerances typically allow +/- 0.05 mm to 0.08 mm variance. However, unscrupulous suppliers exploit this by substituting nominal 0.9 mm (20G) sheet for 1.2 mm (18G). The Steel Guild verifies every sheet with digital micrometers before shearing.

Can stainless steel be welded to mild steel?

Yes, using specialized 309L filler wire which accommodates the metallurgical differential and prevents embrittlement. This is common when mounting stainless equipment to structural mild steel chassis or wall anchors.

What cleaning chemicals ruin 304 stainless steel?

Hydrochloric acid (muriatic acid), concentrated bleach (sodium hypochlorite), and abrasive scouring pads containing carbon steel ruin stainless steel by destroying its chromium oxide passive layer and causing immediate pitting.

Commercial Kitchen Equipment

What stainless steel kitchen equipment does The Steel Guild fabricate in Faisalabad?

The Steel Guild manufactures custom AISI 304 stainless prep tables, single and multi-bowl sinks, commercial canopy exhaust hoods, wall shelving, bakery cooling racks, food service display counters, and complete dishwashing scullery lines.

Can you fabricate custom prep tables to fit specific room dimensions?

Yes. All our commercial kitchen equipment is custom-built to order. We fabricate straight runs, L-shaped corners, and island layouts with exact cutouts for building columns, water conduits, and gas piping.

What features are included in a commercial stainless steel sink unit?

Our sink units feature deep-drawn or radius-welded coved bowls (300 mm to 450 mm depth), 100 mm to 150 mm rear backsplashes, anti-drip rolled marine edges, 38 mm tubular legs with adjustable bullet feet, and pre-punched faucet drillings.

What is an anti-drip or marine edge on a stainless kitchen counter?

A marine or rolled edge is a raised perimeter ridge (typically 5 mm to 10 mm high) formed along the front and side edges of stainless tables to contain liquid spills and prevent greasy runoff onto kitchen floors.

How are commercial prep table tops reinforced against flexing and noise?

We weld full-length 1.5 mm stainless hat channels underneath table surfaces and embed sound-deadening mastic damping tape. This eliminates oil-canning, surface drumming, and flex under heavy culinary chopping.

What type of feet or castors do you install on mobile kitchen tables?

We install heavy-duty 5-inch polyurethane non-marking swivel casters with dual pedal brakes and grease-sealed ball bearings, engineered for dynamic loads of up to 400 kg per 4-wheel set.

What is the standard depth for commercial kitchen work tables?

Standard commercial depths are 24 inches (610 mm) for compact prep stations and 30 inches (760 mm) for primary cookline lines. Custom depths up to 36 inches (915 mm) are built for central bakery preparation.

Do you fabricate GN pan compatible bakery and cooling trolleys?

Yes. We build single and double-bay utility carts with laser-formed L-runners sized precisely for Gastronorm (GN 1/1, GN 2/1) pans or 18x26 inch commercial baking sheet trays with positive pan locks.

Can you integrate sinks, drawers, and waste chutes into a single continuous counter?

Yes. We frequently build continuous multi-station prep tables that integrate deep vegetable wash bowls, knife storage slots, sliding drawer banks, and circular rubberized scrapping chutes directly over waste bins.

What are the sanitation benefits of coved internal sink corners?

Coved corners have a smooth 15 mm to 25 mm radius instead of sharp 90-degree internal joints. This prevents grease, food particles, and bacterial colonies from lodging in corners, allowing rapid wipe-down sanitization.

What is the standard backsplash height for commercial kitchen sinks and tables?

Standard rear splash-guards range from 100 mm (4 inches) for dry prep tables up to 150 mm–250 mm (6 to 10 inches) for wet wash sinks to protect plaster and tile walls from water seepage.

How much weight can a 4-tier commercial stainless storage rack carry?

Our freestanding 4-tier storage units built with 1.5 mm solid or louvered shelves and 38 mm square tube uprights carry 150 kg to 250 kg per shelf level, supporting up to 800 kg total distributed load.

Exhaust Hoods & Ventilation

How do you calculate the correct size for a commercial kitchen exhaust hood?

A commercial kitchen canopy must overhang cooking appliances (burners, tandoors, fryers) by a minimum of 6 to 12 inches (150 mm to 300 mm) on all open sides to capture expanding thermal grease plumes effectively.

What type of grease filters are used in The Steel Guild exhaust canopies?

We manufacture removable, dishwasher-safe AISI 304 stainless steel baffle grease filters. Their interlocking curved vanes force greasy exhaust air to change direction rapidly, separating grease droplets by centrifugal action into collection gutters.

Why are baffle grease filters superior to mesh filters in commercial kitchens?

Mesh filters clog rapidly with grease, posing severe fire hazards and restricting airflow. Baffle filters maintain constant exhaust airflow even as grease collects, and act as a certified flame barrier preventing cooking flare-ups from entering ductwork.

What is the required exhaust air volume (CFM) for commercial restaurant cooklines?

Exhaust volume is calculated based on equipment thermal rating: light duty ovens require ~150–200 CFM per linear foot, medium duty ranges require ~300 CFM per foot, and heavy-duty woks/charbroilers require 400–500 CFM per linear foot of hood length.

What is a grease gutter and drain cup on an exhaust hood?

A grease gutter is a pitched channel running along the lower perimeter of the hood that directs drained grease from the baffle filters into a removable stainless steel drain cup for effortless daily disposal.

Do you fabricate island exhaust hoods as well as wall canopies?

Yes. We fabricate both wall-mounted canopy hoods with flat backs and double-sided V-bank island hoods engineered for central open kitchen cooklines, complete with heavy overhead threaded rod suspension tabs.

What sheet thickness is used for commercial exhaust hoods in Pakistan?

The Steel Guild fabricates all exhaust canopies from 1.2 mm (18-gauge) AISI 304 stainless steel with continuous liquid-tight welded seams to ensure grease cannot leak through joints into kitchen work areas.

Do you supply duct collars and transition boxes with exhaust hoods?

Yes. Every hood is fitted with custom-dimensioned circular or rectangular exhaust duct spigots and transition dampers engineered to match your exhaust ducting diameter and inline centrifugal blower capacity.

Why is make-up air (fresh air replenishment) necessary with large commercial hoods?

When a powerful commercial exhaust hood pulls 2000–5000 CFM out of a kitchen, negative air pressure builds up, pulling exhaust fumes backward and causing doors to slam. Make-up air supplies filtered fresh air to maintain balanced room pressure.

Can exhaust canopies be fitted with heat-resistant LED lighting?

Yes. We provide pre-cut, sealed enclosures for vapor-proof, grease-tight LED lights that provide bright illumination across the cooking line while withstanding extreme heat and washdown sprays.

Steel Fabrication & Gates

What custom steel fabrication services does The Steel Guild provide?

We fabricate heavy automated driveway gates, architectural balcony railings, window safety grills, staircase balustrades, industrial structural equipment skids, rooftop chiller supports, and sheet metal equipment housings.

What steel wall thickness do you use for driveway entrance gates?

We construct main gate outer frames from minimum 14-gauge (2.0 mm) or 12-gauge (2.5 mm) heavy structural hollow sections (SHS/RHS) to prevent gate sag, hinge bind, and structural deflection over time.

Can your driveway gates be motorized with sliding or swing automation kits?

Yes. We pre-engineer gates with reinforced motor mounting baseplates, welded gear rack brackets for sliding gates, and heavy-duty ball-bearing pivot hinges designed for electric linear actuator swing rams.

How do you protect mild steel gates and railings from rusting in Punjab’s climate?

All mild steel fabrications undergo chemical degreasing, mechanical wire wheel de-scaling, a two-coat zinc-rich anti-corrosion epoxy primer, and a topcoat of UV-resistant automotive polyurethane (PU) or thermoset powder coating.

What is the advantage of 304 stainless steel staircase railings over mild steel?

AISI 304 stainless steel railings require no painting, will not chip or rust from hand sweat and humidity, and maintain an elegant, high-end architectural finish with minimal wipe-down cleaning for decades.

Do you fabricate heavy industrial machine skids and equipment bases?

Yes. We manufacture heavy industrial equipment skids utilizing universal steel beams (I-beams), structural channels (C-sections), and heavy plate gussets engineered to support industrial generators, compressors, and chillers.

Can you fabricate custom metal items from an architect’s CAD drawing or sketch?

Yes. Share your architectural drawings, elevation blueprints, or hand sketches with dimensions on WhatsApp (+92 302 3434171), and our team will convert them into production shop cut-lists.

What welding processes do you use for structural steel frames?

We deploy Gas Metal Arc Welding (MIG/GMAW) with solid ER70S-6 wire and argon-CO2 shielding gas to achieve deep penetration, high ductile strength, and uniform fillet welds on structural steel assemblies.

Do you manufacture custom sheet metal enclosures and control panels?

Yes. We shear, CNC press-brake bend, and weld custom stainless steel and mild steel equipment enclosures complete with ventilation louvers, neoprene gasket channels, and internal mounting brackets.

Pricing, Quotes & Guarantees

What information is written on every Steel Guild quotation?

Every quote specifies: exact product dimensions, quantity, steel grade (AISI 304, 316, or mild steel), sheet thickness in true decimal millimetres, weld finishes, site delivery logistics, and fixed total pricing with no hidden charges.

What is The Steel Guild’s written specification guarantee?

We guarantee in writing that the steel grade and decimal sheet thickness delivered match your quote exactly. If laboratory, chemical, or caliper tests reveal non-conforming materials, we replace the piece at our expense or issue an immediate full refund.

Why do metal fabrication quotes vary so widely across workshops in Pakistan?

Price differences are almost entirely driven by down-gauging (substituting thin 0.9 mm 20G metal for 1.5 mm 16G), using inferior 200-series steel instead of food-grade 304, omiting structural under-ribs, and spot welding instead of continuous TIG seams.

Can I check my equipment’s sheet thickness when it is delivered?

Yes. We actively encourage all clients, chefs, and engineers to measure sheet edges, flanges, and leg tubing with a digital micrometer or vernier caliper before signing the delivery acceptance receipt.

Will The Steel Guild audit a cheaper quote from another fabricator?

Yes. Send a photo of any competing quotation to us on WhatsApp (+92 302 3434171). We will audit the line items for free and show you where the vendor is cutting costs on sheet gauge, steel alloy, or structural reinforcement.

Do you charge for on-site kitchen measurements in Faisalabad?

On-site technical measurements and layout consultations within Faisalabad are provided free of charge for confirmed commercial kitchen fit-outs and architectural projects.

What payment terms are standard for custom metal fabrication?

Our standard terms are a 50% mobilization advance upon order confirmation to purchase certified mill raw materials, with the remaining 50% balance payable upon workshop inspection or site delivery.

What warranty is provided against welding defects?

We provide a 12-month structural integrity warranty. If any weld joint fails or cracks under normal operational conditions within the first year, our team will re-weld and finish the piece on-site or in our workshop free of charge.

Faisalabad & Lahore Logistics

Where is The Steel Guild fabrication workshop located in Faisalabad?

Our central fabrication workshop is located on Susan Road, Faisalabad, Punjab 38000 (Plus code: C4FC+JF3 Faisalabad). We are open Monday to Thursday, Saturday and Sunday from 9:00 AM to 9:00 PM (closed Fridays).

Can customers visit The Steel Guild workshop to inspect work in progress?

Yes. We maintain an open-door workshop policy. You are welcome to visit our Susan Road facility to inspect raw sheet stocks, watch TIG welding, and test thickness on current jobs before placing your order.

Does The Steel Guild supply commercial kitchen equipment to Lahore?

Yes. We regularly manufacture and supply commercial restaurants, bakeries, cafes, and builders across Lahore, delivering to Gulberg, DHA, Johar Town, Bahria Town, Cantt, and Sundar Industrial Estate.

Why do Lahore restaurants buy from a Faisalabad workshop?

By buying directly from our Faisalabad manufacturing floor, Lahore restaurant owners bypass high showroom commissions and Lahore distributor markups, saving 15–25% while receiving guaranteed 304 food-grade stainless specifications.

How is equipment transported and delivered from Faisalabad to Lahore?

Finished equipment is wrapped in protective polyethylene surface film and corner buffers, then transported via dedicated flatbed or covered trucks directly to your restaurant or commercial site in Lahore within 2 to 3 hours.

Can your team visit a restaurant site in Lahore for exhaust and counter measurements?

Yes. For commercial kitchen fit-outs and multi-station orders in Lahore, our technical team coordinates on-site site visits to measure kitchen floor dimensions, wall plumbness, and exhaust duct penetrations.

What other cities across Punjab does The Steel Guild deliver to?

Beyond Faisalabad and Lahore, we deliver commercial equipment across Punjab including Sheikhupura, Sargodha, Gujranwala, Sialkot, Jhang, Chiniot, Sahiwal, and Multan.

How long does custom fabrication typically take from order to delivery?

Standard custom prep tables, sinks, and single exhaust hoods typically take 4 to 7 working days. Complete turnkey commercial restaurant kitchen fit-outs take 10 to 18 working days depending on scope.

See our Faisalabad workshop, check how we quote, or explore sheet gauges and steel grades.